| Welcome to Desert Warrior Products: M1A M14 Tools Castle Nut Pliers Hand Guard Pliers Gas Cylinder Wrench. M14 Accessories M1A Accessories |
Tool House For The M1A M14
Everything you'll
need to make,
disassemble and
repair the ultimate
battle riffle!
need to make,
disassemble and
repair the ultimate
battle riffle!
Hardened, Steel Head Eliminates Flex, Prevents Stripping
Thick, steel handles provide the necessary strength and rigidity to
tighten and loosen the flash suppressor nut on M1A/M14 rifles.
Hardened jaw points provide precise engagement to eliminate
notch stripping. Rubber sleeves give a positive gripping surface.
SPECS: Hardened steel, black oxide finish. 6" (15cm) long
Thick, steel handles provide the necessary strength and rigidity to
tighten and loosen the flash suppressor nut on M1A/M14 rifles.
Hardened jaw points provide precise engagement to eliminate
notch stripping. Rubber sleeves give a positive gripping surface.
SPECS: Hardened steel, black oxide finish. 6" (15cm) long
|
Castle Nut Pliers
Fast, Easy Clip Removal; No Broken Handguards
A proven military armorers tool that safely removes the attaching
clip from M1 Garand/M1A top handguards without damage.
High-quality pliers are machined from solid, lightweight aluminum
with oversize handles for controlled leverage and years of lasting
service.
SPECS: Machined aluminum, silver, matte finish. 7" (17cm) long.
Includes illustrated instructions.
A proven military armorers tool that safely removes the attaching
clip from M1 Garand/M1A top handguards without damage.
High-quality pliers are machined from solid, lightweight aluminum
with oversize handles for controlled leverage and years of lasting
service.
SPECS: Machined aluminum, silver, matte finish. 7" (17cm) long.
Includes illustrated instructions.
|
Handguard Clip Pliers
M14/M1A GAS CYLINDER WRENCH - Supports the gas cylinder
so it won't be twisted by the wrench force when unscrewing the
gas cylinder plug. Makes it possible to separate these parts in the
field without a vise. Also has a hole and lock screw to hold the gas
piston stem during cleaning.
SPECS: Aluminum. 6" (15.2cm) long x 1½" (3.8cm) wide x 5/16"
(7.9mm) thick.
|
Gas Cylinder Wrench
M1/M1A RECEIVER/BARREL TIMING GAUGES - Machined
aluminum gauges give a precise, repeatable indexing reference
so front and rear sights can be aligned perfectly, every time.
Front gauge attaches to the gas cylinder (M1) or flash suppressor
(M1A); rear gauge fits in the stripped rear sight housing.
SPECS: Machined aluminum, silver, matte finish. 6" (15cm) long,
1" (2.5cm) square. Includes illustrated instructions.
|
Receiver/Barrel Timing Gauge
M14/M1A STOCK LINER NUT DRIVER - Provides non-slip
engagement for removing stubborn stock liner nuts on wooden
M14 and M1A rifle stocks.
SPECS: S-7 steel, 1" (2.5cm) long, ¼" hex drive.
|
M14/M1A Stock Liner Nut Driver
M14/M1A BOLT ROLLER GREASER - Pushes grease into the
roller and around the lug for maximum protection from failure. Put
a small amount of your favorite, high-bodied grease on the tool's
recess and push it against the bolt roller. It's that fast and that
simple; the roller gets greased, your hands stay clean.
SPECS: Delrin body, steel handle. 2" (5cm) long.
|
Bolt Roller Greaser
Provides Safe & Secure Installation & Removal Of Gas Lock
Front Sights
Current military issue wrench supplied with the Smith Enterprises
“Crazy Horse” M14 Sniper Rifles ensures gas lock front sight body
cannot be damaged while doing routine field maintenance. Fully
cradles and supports the gas lock front sight and helps provide
precise alignment during reinstallation. Hole with steel cross pin
allows wrench to double as a convenient and foolproof holding
fixture for removing carbon build from the gas piston body.
SPECS: 7075 T6 aluminum, clear hard anodized gray, matte
finish. 6”(15.2cm) long, 3⁄8”(9.5mm) thick. 1oz. (28.3g) wt.
Front Sights
Current military issue wrench supplied with the Smith Enterprises
“Crazy Horse” M14 Sniper Rifles ensures gas lock front sight body
cannot be damaged while doing routine field maintenance. Fully
cradles and supports the gas lock front sight and helps provide
precise alignment during reinstallation. Hole with steel cross pin
allows wrench to double as a convenient and foolproof holding
fixture for removing carbon build from the gas piston body.
SPECS: 7075 T6 aluminum, clear hard anodized gray, matte
finish. 6”(15.2cm) long, 3⁄8”(9.5mm) thick. 1oz. (28.3g) wt.
|
Gas Lock Front Sight Wrench
Simplifies Assembly & Disassembly
Proven armorer's tool makes both assembly and disassembly a
simple, one-hand task by capturing the hammer, plunger and
spring so the pin can be removed, or inserted easily. Steel fixture
is pre-drilled; can be attached to the bench for production work.
Works for M1 Garand, M14 and M1A.
SPECS: Steel, blued. 4" (10cm) wide, 2" (5cm) high, 5/8" (15mm)
thick. Includes instructions.
Proven armorer's tool makes both assembly and disassembly a
simple, one-hand task by capturing the hammer, plunger and
spring so the pin can be removed, or inserted easily. Steel fixture
is pre-drilled; can be attached to the bench for production work.
Works for M1 Garand, M14 and M1A.
SPECS: Steel, blued. 4" (10cm) wide, 2" (5cm) high, 5/8" (15mm)
thick. Includes instructions.
|
Trigger Group Assembly Tool
Provides Perfect Zero, Windage Alignment
Machined sight tool accurately repositions the front sight to
properly align with the rifle’s mechanical zero point, plus holds this
position when installing a new front sight. Non-marring, aluminum
tool body fits over the flash suppressor; nylon thumbscrew
secures it. Stainless steel, sight pusher is calibrated to match
windage clicks for standard and National Match rear sights. Relief
cut allows you to remove the sight without moving the tool.
Includes instructions.
SPECS: Aluminum, anodized silver. 1¼" (3.2cm) long, 1¼" wide, 1-
9/16" (4cm) high.
Machined sight tool accurately repositions the front sight to
properly align with the rifle’s mechanical zero point, plus holds this
position when installing a new front sight. Non-marring, aluminum
tool body fits over the flash suppressor; nylon thumbscrew
secures it. Stainless steel, sight pusher is calibrated to match
windage clicks for standard and National Match rear sights. Relief
cut allows you to remove the sight without moving the tool.
Includes instructions.
SPECS: Aluminum, anodized silver. 1¼" (3.2cm) long, 1¼" wide, 1-
9/16" (4cm) high.
|
Front Sight Tool
Cleaning Drill Set
|
The cleaning drill set includes a
#15 (.180 dia) & Letter ‘P’ (.323
dia.) drill for scraping the carbon
deposits from the internal bores.
The drill handles are CNC
machined from the same type of
6061 aluminum with a comfortable
ergonomic design.
#15 (.180 dia) & Letter ‘P’ (.323
dia.) drill for scraping the carbon
deposits from the internal bores.
The drill handles are CNC
machined from the same type of
6061 aluminum with a comfortable
ergonomic design.
After removing the gas plug using the Sadlak Gas Cylinder Wrench and
a USGI Combo Tool (or a 3/8 box wrench), insert the new "O" drill into the
gas plug to scrape and remove carbon deposits.
a USGI Combo Tool (or a 3/8 box wrench), insert the new "O" drill into the
gas plug to scrape and remove carbon deposits.
Gas Plug Drill
|
The aluminum model is CNC machined from ½ thick aircraft quality 6061 heat-treated aluminum. The
thicker material and large beveled edges provide added comfort.
The Steel model is CNC machined from 1/4 thick steel with a smaller beveled edge. Both wrenches are
designed to fit all original USGI and most commercial gas cylinders.
Oversized-Wrench - For foreign made gas cylinders, we offer an over-sized version available only in ½ thk.
alum.
thicker material and large beveled edges provide added comfort.
The Steel model is CNC machined from 1/4 thick steel with a smaller beveled edge. Both wrenches are
designed to fit all original USGI and most commercial gas cylinders.
Oversized-Wrench - For foreign made gas cylinders, we offer an over-sized version available only in ½ thk.
alum.
Gas Cylinder Wrench
|
M1A/M14 KIT - Includes four-piece steel cleaning rod,
patch loop tip, .30 caliber bronze bore brush, M14
tapered chamber brush, M14 combo tool, dual-reservoir
oiler and O.D. green rod pouch.
SPECS: Rod, M14 tool and patch loop - steel, blue,
matte finish. Brushes - brass core, bronze bristles.
Pouch - canvas, O.D. green. 9 oz (255g) total weight.
Chamber Cleaning Brush
Proven Military Design For Cleaning Semi-Auto Rifles
Offset, ratchet design gives easier, more thorough
chamber cleaning for any semi-auto rifle with a
closed-end receiver. Premium-quality, bronze wire,
bonded between twisted steel loops; soldered at the tip
for extra strength. Use a ¼" diameter cleaning rod to
actuate the ratchet.
SPECS: Plastic ratchet, bronze wire. 4" (10cm) long. Fits
.308 chambers only.
patch loop tip, .30 caliber bronze bore brush, M14
tapered chamber brush, M14 combo tool, dual-reservoir
oiler and O.D. green rod pouch.
SPECS: Rod, M14 tool and patch loop - steel, blue,
matte finish. Brushes - brass core, bronze bristles.
Pouch - canvas, O.D. green. 9 oz (255g) total weight.
Chamber Cleaning Brush
Proven Military Design For Cleaning Semi-Auto Rifles
Offset, ratchet design gives easier, more thorough
chamber cleaning for any semi-auto rifle with a
closed-end receiver. Premium-quality, bronze wire,
bonded between twisted steel loops; soldered at the tip
for extra strength. Use a ¼" diameter cleaning rod to
actuate the ratchet.
SPECS: Plastic ratchet, bronze wire. 4" (10cm) long. Fits
.308 chambers only.
M1A/M14 Cleaning Kit
|
We Proudly Accept
Tactical Stocks
Troy Industries
Sage International
Vltor Tactical
Troy Industries
Sage International
Vltor Tactical
Other Accessories
Magazines Cleaning Supplies
Forward Rail Replacement Parts
Soft Gases Rings & Accessories
Hard Cases Bi Pods
Slings Cheek Rest
Magazines Cleaning Supplies
Forward Rail Replacement Parts
Soft Gases Rings & Accessories
Hard Cases Bi Pods
Slings Cheek Rest
| New Products |
| Tool House |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
EOTech Optics
Balastic Drop
For the .308
Balastic Drop
For the .308
 |